Fabric License and Full Fabric License
Hello All! Are the fabric license and the full fabric license different licenses or just different names for the same license? Thank you if you answer.
View ArticleBrocade and ADVA FSP3000 Compatibility Matrix
Hello, IHAC thats has delpoyed a WDM ADVA FSP3000, so I'm looking the compatibility Matrix for 6510 and 300. The customer i using the following board: 1063707620-01...
View ArticleDS24M2 manual?
Trying to get information on an a fiber switch rebranded to MC Data DS-24 M2. Been digging for a few hours trying to find the manual. MC Data support points to Brocade. Brocade doesn't have the model...
View ArticleDisabling http
All, the FabricOS (6.1.1) documentation section that describes enabling https shows an example of the configure command with http attributes as an option under the "System services -> ssl...
View ArticleShutdown a switch properly
Few of our switches doesn't Power I/O buttron on the rear/back side of the switch. What is the right process for to power off these kind of switches (don't want pull-out the power cable) ?
View ArticleDCX SNMPv3 Config DCFM
Hi, I have below setup for snmpv3 configuration on DCX switch. But under the DCFM >>Discovery >> setup it show error message. The user and password are correct for MD5 and DES, It will be...
View ArticleHow to connect two FC-Switches
Hi I want to connect two Brocade FC-Switches. When I do that I see on Switch1: >switchshow Area: 3 Port: 3 Media: id Speed: N2 State: Online E-Port segmented,(disabled E_Port) Switch2:...
View ArticleBrocade Slikworm 200E password recovery
Dear All, Badly need help as i am going through a hard time , to recover the Brocade Slikworm password . your guidence will be highly apperciated in this regard . regards, AD
View ArticleI/O Latencies & Timeouts in our SAN Fabric Brocade 5300s - v6.4.0b
We have SAN Fabric configuration with Brocade 5300s running FOS v6.4.0b. Each of our two floors (1 & 2), served by a Brocade 5300, floor's local hosts and storage, and these two switches are...
View ArticleReset counters displayed by command Porterrshow??
How do you reset the counters displayed when the "porterrshow" command is issued?? We are trying to debug a problem and showing counters from power-up confuses the issue. Thanks Much In Advance Ron...
View ArticleHigh and continous er_enc_out and er_bad_os
Hi Guys, I am observing very high errors on a port. er_enc_out and er_bad_os are increasing rapidly. every second there are about 50 errors.Can anyone help to know the reason for this issue. Thanks...
View ArticleReset a san switch to factory defaults
Hi. Could someone please tell me how could i reset a 200E san switch to factory defaults? can this be done via telnet or must i connect to it using a serial cable? Is there a guide on this? Best...
View ArticleProblem with ssh and publickey authentication
Hi all, When I connect via ssh to a 4100 switch running FOS 5.2.0a or 5.3.2a using password authentication, everything works fine. When I use public key authentication, I get logged in but the...
View ArticleBrocade 7800 fcip tunnel with one circuit on two gbe ports
Hi, I have to configure fcip tunnel with one circuit on two gbe ports on Brocade 7800 routers on both sites. When ipaddress is assigned, do I need to assign separate ipaddress to both two gbe ports...
View ArticleSkillworm EMC-Ds-200(password reset)can't connect trought Hyperterm
Hello I have purchased a skillworm EMC(brocade) DS200 NO idea what the password is it powers up correctly it goes troughtthe normalpower process then stays green(powerlight) the Lan ports shows...
View ArticleFabric watch : all actions to none
Hi everyone, I have installed fabric watch which sends trap to our enterprise system management. But in purpose to not flood the latter, I want to set all the actions to "none" by default then choose...
View ArticleMassive upgrade of backend switches skipping versions in between
Hello everyone, I know that the supported solution is to do upgrades of Brocade switches with one version hops. However a customer is facing requirements to upgrade ~1500 Silkworm 5100 switches which...
View ArticleDomain id and zone info are missing
Hi experts, I am new here. I found GUI of brocade SAN switch is weird. 1. Zone info will disappear(become empty) after a couple minutes.(see screenshot 1, the info is correct at beginning.) 2....
View ArticleCRC Errors on E_Port
I have 2 x 4G FC DWDM Circuits connected to the ports from same ASIC truncked.. connected b/w 2 DC's sharing resources b/w DC's. Seeing lot n incresing CRC and Invalid_words errors on the E_Ports...
View ArticleImplementing ficon on DCX-4S
Hi, What are the parameters/settings to be enabled when implementing ficon on DCX-4S switch? I have an existing DCX-4S switch on production which is catering fcp devices, now we are connecting a...
View Article