Hello Everyone, I have filled the "upgrade access" form on MyBrocade with a valid serial number, in order to download firmware upgrade for two Brocade 5000 Switch. I did not received any contact from Brocade and still don't have access do download
↧
Upgrade Access - Download Firmware
↧
How to recover admin or root password.
Hello, I have sigle fabric swith brocade 300, OS version 6.3.1B, i need to know what is the process for recover root or admin password
↧
↧
Problem with Brocade 815 direct attached to storage
I have an IBM server with 2 single port Brocade FC cards (815) running Windows 2008 R1 x64. Each card is directly attached to a separate controller on an IBM storage solution (DS3512.) When the DS3512 is reset, the cards connect to the
↧
I/O Latencies & Timeouts in our SAN Fabric Brocade 5300s - v6.4.0b
We have SAN Fabric configuration with Brocade 5300s running FOS v6.4.0b. Each of our two floors (1 & 2), served by a Brocade 5300, floor's local hosts and storage, and these two switches are connected by TWO 8 Gbps ISLs (trunked on port#0 and
↧
How to connect two FC-Switches
Hi I want to connect two Brocade FC-Switches. When I do that I see on Switch1: >switchshow Area: 3 Port: 3 Media: id Speed: N2 State: Online E-Port segmented,(disabled E_Port) Switch2: >switchshow Area: 4 Port: 4
↧
↧
Why some wwns not visible in the Access Gateway are visible in the switch Fabric
Hello everybody, I will appreciate any input that help me to understand what is happening in the following issue : I have an IBM Blade Center working with NPIV connected to a Brocade switch configured as Access Gateway and the N
↧
Portcfgfillword and 16Gb DCX 8510 and 6510 switch ports set to 8Gb
I no longer see the portcfgfillword listed under the portcfgshow on the brocade 8510 and 6510 switches. You may say it does not apply to a 16Gb port, but what happens if, by chance, want to set this port to 8Gb? I have had to set some
↧
License in Brocade 6510
Estimates, for the brocade 6510 FOS 7.0.0, I must install the Extended Fabric license, or it is already embedded in the same? Thanks and regards
↧
Live migartion from 5100 to 6520
Hello All, We have two 5100 and all the ports are full.We are going to migrate to 6520. It's all production hosts and is installed with powerpath. we are using soft zoning.Can anyone send me the proper steps to be done for the live migration?
↧
↧
How do you connect to fiber switches?
I have a new IBM Blade Center H with 2 internal fiber switch modules. 6 external ports / 14 internal ports. I have an existing DELL / EMC SAN running on 2 McData DS4700M 32 port switchs. I'd like to connect the Blade switches to the existing switches
↧
Port in G-Port status after switch reboot
Hello. Having HP B-series 8/12c SAN Switch BladeSystem c-Class(Brocade) blades in c7000 enc with QLogic QMH2562 8Gb FC HBA for HP BladeSystem c-Class. On blade ESXi 4.1 update1 installed. SAN Switch OS is 6.4.1b After reboot of SAN Switch
↧
admin password reset silkworm 2800 (firmware v2.6.0c)
We just purchased an old silkworm 2800 SAN Switch. We do not know the admin password, and I have tried resetting to factory defaults. But it is not resetting the password. I read somewhere that there was firmware fix to stop from resetting the
↧
Skillworm EMC-Ds-200(password reset)can't connect trought Hyperterm
Hello I have purchased a skillworm EMC(brocade) DS200 NO idea what the password is it powers up correctly it goes troughtthe normalpower process then stays green(powerlight) the Lan ports shows as active but
↧
↧
Chassis is not ready for management now. Please try after some time.
I am having this issue with a 48000 director with FW 6.2.0g after adding it to the Fabric. There are 30 switches in the fabric and all are accessible via telnet. Webtools works on all but the 48000 which says "Chassis is not ready for management now.
↧
Brocade 300 not merge fabric with Brocade 4/24 SAN Switch for HP c-Class (type 43.2)
hi, I have an existing fabric with two Brocade 4/24 SAN Switch for HP c-Class (type 43.2) I want to add a new Brocade 300 but when i link together show this error brocade 300 (FOS v7.0.0a) B300:admin> switchshow
↧
B300E switches and the best devices to do FC over IP to a DR-Site.
We have several Brocade B300E switches setup in a Small Fabric. I have been asked to research what is the best way to do FC over IP to a DR-Site. I am told there is a set of McData Eclipse 1620 available. What is the best way or devices to do
↧
Brocade SAN switch password change
It seems the correct way to change password for 'admin' user is simply login as 'admin' and type 'passwd', also the same way is true for changing 'root' user's password. Could someone please confirm? Thanks,
↧
↧
Reset counters displayed by command Porterrshow??
How do you reset the counters displayed when the "porterrshow" command is issued?? We are trying to debug a problem and showing counters from power-up confuses the issue. Thanks Much In Advance Ron NOTE: This content was migrated by Brocade from
↧
What is a seed switch?
Can anybody tell me what is a seed switch and what are its functionalities?
↧
Forcing the domain ID on a switch
Hello, I want/need the domain ID of a swith to be set to an arbitrary value. I've tried on a "standalone" switch running with DID 1 up to now. It sort of made me think it accepted the change, but on the web
↧