Hi, I'm trying to configure ISL between Brocade 3250 and Brocade 300 switch, but i have this error messages : on the brocade 3250 : incompatible flow control parameters and the brocade 300: ELP rejected by the other switch - FOS
↧
ISL Between Brocade 3250 and Brocade 300
↧
ISL trunking between Brocade 4900 and DCX-4S Director
Hello Team, I am new, and please I would like to share your experience in ISL trunking. In our DataCenter, I have a Brocade DCX-4S. I would like to extend my fabric to a second data center far from 200m. Between the two data centers, We have
↧
↧
cannot load RBACMatrix
I have a Brocade DS5000 getting this error. My client java version is 1.5.0_20 DS5000 Current HTTP configuration javaplugin.version = 1,5,0,6 javaplugin.homeURL =
↧
How to identity and monitor "Slow Drain Devices"?
Hi All, Recently i have been dealing with some slow drain devices in our SAN wich are impacting a bunch of AIX Hosts. On host side we received a lot of Temp "SC_DISK_ERR4" errors and we can identify that response time increses as well. In
↧
How I can upgrade firmware Silkworm 48000?
How I can upgrade firmware Silkworm 48000? Can I upgrade online ? I want to backup firmware and configuration before upgrade. Please, help to suggest me to backup and upgrade firmware.
↧
↧
Merging two fabrics
Hi, We need to merge two fabrics into a big one, each switch has a unique domainid, port zonning. each fabric has its own configuration active. What is the procedure to merge them? Should they merge automatically? in that case which configuration should
↧
Severe latency bottleneck detected on ISL / Trunk port
Hello, could anyone give me a hint how to troubleshoot error "Severe latency bottleneck detected" on ISL/trunk port? What can cause this problem and how a root cause can be found? We received this alert on trunk created from two 8Gbit
↧
Brocade 7800 fcip tunnel with one circuit on two gbe ports
Hi, I have to configure fcip tunnel with one circuit on two gbe ports on Brocade 7800 routers on both sites. When ipaddress is assigned, do I need to assign separate ipaddress to both two gbe ports and one circuit OR only assign ipaddress to only
↧
invalid domain ID -1 when doing performance query
Hello, I have 2 switches that I inherited with the job and every time I click the "Perf" icon I get the following message: "Invalid domain ID -1 or domain is missing in fabric info data page" I recently changed the domain ID on 1 of them but not on
↧
↧
Port random timeouts/resets on ISL over DWDM
I have two DCX directors connection through the Cisco DWDM 15454SDH over 4Gb and 2Gb ports, two different providers distances 15 and 20 km.DWDM is the card I think TDM with ports with speeds 1,2,4 Gb. On DCX is using Exchange-based policy routing. The
↧
To migrate from 48000 to DCX non-distruptive.
Hi All, We are planning to upgrade our current fabric set up consisting of 6*48000 directors per fabric (ruuning in half mesh topology) to DCX in Core-Edge topolgy(2 cores and 4 edges). We were planning to perform like this 1.
↧
CRC Errors on E_Port
I have 2 x 4G FC DWDM Circuits connected to the ports from same ASIC truncked.. connected b/w 2 DC's sharing resources b/w DC's. Seeing lot n incresing CRC and Invalid_words errors on the E_Ports (inter connected b/w DC's) where DWDM link is
↧
ISL zone conflict between switches
Hi, I have a 2109-F16 IBM switch and a Brocade 3900 switch with an ISL installed between them but the fabric has segmented with a zone conflict and the fabrics failed to merge. Is this because the configurations on both switches have different names or
↧
↧
DS24M2 manual?
Trying to get information on an a fiber switch rebranded to MC Data DS-24 M2. Been digging for a few hours trying to find the manual. MC Data support points to Brocade. Brocade doesn't have the model listed. Created a profile here, and it asks me what
↧
does enc out counter means bad?
Hello, We have two switches in a fabric. On ISL port we observed enc out errors. I read enc out and crc err together means sfp or cabling problem. s152f003-sw01:admin> porterrshow
↧
Lots of "link fail", "loss sync" and "loss sig" errors
Hello, I have two Brocade 3850 switches (FOS - 5.3.2a), which have a lot of "Link Failure", "Loss of Sync" and "Loss of Signal" errors on their ports. Ports no. 2 and 8 on switch no. 1 and ports no. 4 and 8 on switch no. 2 are especially "dirty"
↧
Add a switch to an existing fabric
Hello all, actually I've a fabric made up by two switches, A and B. I've to add a third switch, called C. First I've connected one port of C to A and one port of C to B. Switch A is domain 1, switch B is domain 2. Switch C is domain 1. Of course
↧
↧
Error messages FW-1436 and FW-1424 in my Brocade logs
Hi All, I have got an alert from my IBM DS storage stating Logical Drive is not through the preferred path later was able to see error messages in my Brocade switch event logs with message ID's FW-1436 and FW-1424. Please help me to confirm what
↧
Blocked FC remote port time out: removing rport
I am kinda in the dark here, hope this is correct forum for feedback. We have QLogic QMC2462S HBA's connected to Brocade 4020 (IBM BLADE) connected to Brocade 200E Switch and then connected to our SAN controller (IBM). We have 14 blade
↧
Serial Number
Hi! Is there a way to get the Serial Number of the Switch-Hardware ? (telnet, browser) Silkworm 3800 and 3900. Thanks CK. NOTE: This content was migrated by Brocade from the former Brocade Connect community on March 10, 2008, on behalf of the author.
↧